Fuji Build… O boy!

On with the Build!!!

I have had a busy week but I managed to get an hour or so into the bike and this is what I have gotten done.

I know the rear derailleur is not on there but just a pic of the setup

-Rear wheel. Barely had enough clearance in the frame. It sits real tight but that should not be a problem since it is made for 26ers

-Bottom Bracket. I was lucky enough to have the same 68mm and correct spindle length bottom bracket that it just happened to swap perfectly.

-Cranks. This also goes with the BB but they swapped over just the right length and we are go to go on there. It has a little bit less clearance than on the rockhopper but it is enough!

-Disc Brakes. Both front and rear went on like cake walk. Some minor adjustments had to be made but nothing major. So far so good for cabling transferring over on the right length.

Shot of the rear disc brake

-Rear Derailleur. The Shimano swapped over very easily thanks to a standard bolt.

-Front┬áDerailleur. This caused a bit more of a problem. I had a top-pulling derailleur from the rockhopper and that just wasn’t going to work with the new frame. I needed a traditional derailleur so I went to the LBS to pick up a Shimano Deore for the frame.

Side view of a traditional front derailleur






-Front┬áDerailleur. This caused a bit more of a problem. I had a top-pulling derailleur from the rockhopper and that just wasn’t going to work with the new frame. I needed a traditional derailleur so I went to the LBS to pick up a Shimano Deore for the frame.

Another view of the Front Derailleur

Here is the makeshift headset in order to bring it to the LBS





















-Headset. Biggest pain in the butt I could have imagined. When I bought the frame I saw that it was an integrated headset, no problem. I would have to buy a new headset but thats not a big deal. So I get onto Cane Creek and go to the headset finder. So far so good, right? I get to Fuji then model. Adventure comes up but it says 2010 model only. I found out that the “new” Fuji Adventure is a hybrid bike not my full suspension mountain bike. So I call up Cane Creek and they tell me to take some measurements. Of course I don’t have calipers so this is almost impossible to get absolutely accurate when they come within millimeters of each other. After that failed attempt it was off to the LBS to see if they can help. He figured out the headset and ordered one. Wrong! I guess it is a weird looking zerostack because the intergraded for those measurements did not fit. So I had to leave it there overnight while they get the right one in. So I will be picking it up soon!



I will post more pics of the details once I get the bike back.


Bike Stand Part II – The GRIP!

So after some thinking and input from some people, I finally figured out a solution on the clamp on my bike stand. As you recall from previous posts, I was struggling to find a way to clamp the bikes into the stand and not have them twist and turn while clamped. In order to do this, I came up with the idea of taking an old bike tube and cutting it into sizable chunks then laying it over the wood blocks that I cut out for holding the seat posts.

I went to my local bike shop and they gave me a weird look when I asked for some old mountain bike tubes but after explaining what I was doing, the guy was really interested and asked me how I made it. I think he might make one, thats how pumped he was to hear about it.

Anyways, When I got back to the house, I found out that it was not going to be as easy as planned. Long story short, after fitting and trying to size it up multiple times, the old blocks just were not going to work. I made new block and then cut the tubes to size and made relief slits on top so the rubber would fold flat against the wood.

and the test…. YES! It works! I can now crank on the bike if need be (crank pulling (no pun intended), bottom bracket removal, etc).

I forgot to take a pic of the wood block so I will do those once I get the chance and just add it onto this post.

DIY Project 1= check!

Fuji Full Suspension FrameFrame

So I went into my Local Bike Store (LBS) that just opened and was looking around and they were selling a full suspension bike frame for cheap. I looked into it more and decided that I should go ahead and buy it. I figured since I bought a hardtail (’06 Specialized Rockhopper Comp Frame) frame to do a swap, I might as well just get a full suspension frame and not swap onto the hardtail frame. It is a 2005 Fuji Adventure Hi Full Suspension mountain bike frame (21″). So here we go… I am just about to start swapping parts (posts to come!)


DIY Bike Stand Tray

So as I was looking at the bike stands online, I came up with another idea… A bike repair stand tray


Mechanics use trays to hold tools, parts, coffee, anything they need really.


Here is how I made mine…


Tools List:


-Finishing nails or regular nails (depends on the look you want)

-Saw to cut wood


Parts List:

-Piece of plywood (size depends on how big you would like the tray, I found a scrap piece I had kicking around that is about 18″ long and 9″ wide)

-Wood for edges (size depends on how deep you want the tray, I found scrap again and that was 1″x2″ high)

-1″ U-pole clamp (hint: found in the electrical section of Home Depot)


I cut the plywood down to size that I wanted. I then drilled a 1″ hole about 1″ in from the back and in the centered the hole. Once I drilled that, I tested it for size on the 60″ rigid pipe. Hint: if it is too big, put duct tape around the pole and slide the tray over that! Once you see that it fits, Pull it off and cut the edge pieces to proper length. Nail into side of plywood. Place the U-clamp in position of how high you want the tray to sit. Tighten the U-clamp and slide tray over the top so it sits on the U-clamp. And… DONE! Quick and simple yet very useful (and it save the back!).

Top view: notice how I used duct tape to help shim around the hole of the tray

U-Clamp (found in electrical section of Home Depot) which the tray just sits on

Another view of the tray top and edges


Remember to post pics of YOURS!!

DIY Bike Repair Stand Thoughts

I was just thinking of ways to improve this stand. With the towel wrapped around the seat post, the bike can twist (not ideal). I tried using some foam pipe insulation that I had laying around but that didn’t do much…


I am trying to find some sort of rubber (maybe a old bike tube) that I could use that is not smooth and would “catch” the seat post. I am thinking I might just have to go riding more to get a new tube or take a visit to the LBS to see if they have any laying around.


Any ideas about what I could use?

A First…

This morning marked a first for me… giving a technique lesson to an amateur triathlete.

This proved to be a bit harder than I thought. I have a great knowledge of swimming seeing as I am a swimmer myself. I know the technique part and know it well but teaching it to a person is harder than it looks/appears. I made it through some technical difficulties with the camera (not a good first impression :/ ) but I believe that he knows that I am knowledgeable and know what I am talking about. Mixing my swimming experience with my knowledge of technique and exercise science and I am a coach in the making!

…Well maybe not quite but everyone has to start somewhere right?